CIRCLES ARE OVAL?
I'm having problems. I'm printing oval pulley gears instead of circle pulley gears! I'm trying to print CIRCLE Pulleys I never had this problem until I went from a 8tooth pulley to a 18tooth pulley...
View ArticleRe: CIRCLES ARE OVAL?
Thanks For Your Fast Response(tu) KingRahl Following the video response works like a charm. Thanks Again! B)-
View ArticleRe: Sanguinololu 1.3a, Marlin and Sainsmart lcd
Guess this thread is best for asking my similar question as well: Sanguinololu 1.3a but with Repetier firmware, and the same display type - could be from the same Sainsmart. Now, the problem is - I...
View ArticleRe: Sanguinololu 1.3a, Marlin and Sainsmart lcd
Hi bujholm I did run the Sainsmart LCD controller with Sanguinololu and the Marlin software. When I bought the LCD, came with an adapter for the extension pin header of the Sanguinololu . Have you the...
View ArticleRe: Sanguinololu 1.3a, Marlin and Sainsmart lcd
Hi robbyg, I have the same display as pictured here: [www.geeetech.com] and I do have the right adapter - the one that reconnects the 2 groups of 10 pins into a group of 14 and a group of 6 pins As...
View ArticleRe: Sanguinololu 1.3a, Marlin and Sainsmart lcd
Hi bujholm, If your display is to the geeetech.com I think there's a problem. From what I could see it is a I2C display instead should be SPI. In the I2C case the communication is done via two wires...
View ArticleHeater not heating up above 140C
Hi all, I finished assembling the printer. When I first connected the heater and thermistor, I heated it up, it quickly went till 185 and maintained it. Now I have assembled every thing and want to...
View ArticleRe: Heater not heating up above 140C
If you reached that temp before, you don't have a power issue. What kind of heater are you using? Resistors: Either you have a foil type resistor, which burns out quickly (1-2 uses). Or the wire wound...
View ArticleRe: Using L297/L298 with Sanguino
hey Traumflug !! nice work man :) can you share the firmware of reprap while using stepper driver 1.2 thanks
View ArticleRe: [done] SL 1.3 pauses or disconnects mid-print
I have a Prusa Sanguinololu 1.3 with a ATMega 1284P running Marlin and using a Panelolu2 LCD/SD reader and have experienced resets mid-print (stops and looks like it just turned on - extruder and bed...
View ArticleRe: sanguinololu and marlin thermocouple error
it works with the new version of marlin... also since then i have changed to ramps and a thermistor...;)
View ArticleDid my motherboard die on first try? :X
Hello guys, Quick presentation, I am 32, French and live currently in Shanghai. Hobbies: Marine tank, remote control helicopter (TREX600 nitro), DIY stuff (arduino for aquarium) and new comer in 3D...
View ArticleFried Sanguinololu? I shorted pins....
Hey all, This will be one of my first posts. I've had my rep-rap running for over a year. Loving every second of it. I'm using it to prototype new products at work even. I decided to do a quick...
View ArticleRe: 2nd hand Sanguniololu 1.3a - Setup / Connection troubles
does this help [forums.reprap.org]
View ArticleRe: Fried Sanguinololu? I shorted pins....
If you plug it in via USB, there isnt enough power to move steppers etc, it only provides 5v. It sounds like you have at least toasted the 5v regulator, first thing is to replace that. (and maybe c5...
View ArticleIt's my Third Motherboard and, I just want my printer to move.... Please Help
So I'm trying to get my printer to move with the Sanguinololu. I bought it from a "good ranking" Amazon seller who claims it has been tested. It's has an Atmega 1284P with 16Mhz ceremic oscillator....
View ArticleRe: It's my Third Motherboard and, I just want my printer to move.... Please...
1) all prior version are the arduino IDE are still available see [arduino.cc] 2) avrdude: stk500v2_ReceiveMessage(): timeout" is a communications error so the code compiled fine. Two common causes,...
View Article